How to build a full length storage cabinet

If you aren’t feeling okay with your small storage cabinets, then you’re in the right place. A full-length storage cabinet is the best choice for you.

You can store many things in one cabinet. And you don’t need to buy one because you can build it by yourself. But how to build a full-length storage cabinet? Don’t worry. In this article, you can know the entire building plan of a full-length storage cabinet.

Before starting the procedure, you need to set the whole thing in your mind. Collect all the necessary tools to build the cabinet. Select a design and determine its height, depth, and width. Then you can start the construction. However, let’s know the full strategy of building a full-length storage cabinet.


An ordinary cabinet and a full-length cabinet are almost the same. The only difference is in length. You can build it as a single unit or by stacking two cabinets, one on another.

The two-compartment design requires two pairs of separate doors. Small parts go in the top, and large canisters go in the bottom. You can also input drawers in it if necessary.

Required tools and supplies

To make a homemade storage cabinet you need some tools and equipment. And these are:

  • Undersized ply router bits
  • Wood glue
  • Table saw ripping blade
  • Parallel clamps
  • Center punch
  • Euro style cup hinges
  • Cordless drill
  • Lacquer finish
  • Forstner bit
  • Square
  • Double square
  • Tape measure

How to build a full-length storage cabinet?

In construction, you need to follow some steps. You require to make the side panels, assemble the top and bottom support, add shelves, assemble the back, and assemble the top. And finally, you will paint it.

Now, we’re telling you the construction process elaborately.
Cut all the wood with a suitable size. Construction starts from pre-finished 3/4 plywood by making the carcass. For the project, the cabinet calculator will give you a cut list. You have to build the top, bottom, and side dados, just as shown on the cabinet calculator page.

Joint the dados with each other appropriately. To join the dados, you can use screws and wood glue. You will apply the drill machine to set the screws. The screw and glue make the carcass sturdy.

You can avoid the screws if you do not want to display any fasteners. Without these, the cabinet is strong enough.
A solid poplar face strip can make your shelve aesthetic and robust. That’s why you can use it on your shelf. You can use the polar face strip to make the shelves fixed in place.

Now it’s time to make a face frame. To make a face frame, you need hardwood. So, you may use polar. To attach the frame with the carcass, you will use glue and nails. Nail holes will not be a problem as you paint the frame finally.

On the table saw, the frame pieces dimension easily. With glue and a screw, you can join the pieces in each corner in a pocket hole. Kreg makes several machines and jigs to cut pocket holes. Then, with glue and nails, attach the finished frame to the carcass. For this task, there need lots of clamps because one every 10 inches confirms an accurate result.

Door construction for full-length storage cabinet

You’ve learned to make a cabinet body till now. But, How to build a cabinet with doors? Well, you don’t need to worry. To construct the doors, you can use stile and rail.

For proper width and height of the doors, there needs a correct dimension of stiles and rails. Shaper cut the joints. On the rails and stiles, these shaped joints create locking profiles.

On the table saw, cut two stiles, two rails, and a panel. Then on the rail, cut the end profile. In this operation, a miter gauge or coping sled helps you.

Next, on the rails and stiles, cut the profile. Along all stiles and rails sides, the profile is easy to cut. With the grain, it aligns. The cutter setup is the most challenging part. Until the cutter fits into the gauge block’s profile, increase it.

Then, cut the profile of the panel. Because of the cutter head’s high mass, the profile of the panel is a risky cut. In place of one big one, around the panel, make multiple smaller passes.

Now on the panel, cut the relief cut. Around the panel, on the other side of it, a relief cut makes a lip. Into the groove on the stiles and rails, it fits. The panel only fits into the groove. Until it happens, move the cutter to the workpiece.

Now it’s time to assemble. Like a jigsaw, the pieces must fit together after machining. Put on the stiles and rails around the panel. Then pull these together. Tightly join all joints.

Then look at the back of the panel turning the door. Around the panel perimeter, the relief cut makes a ridge. Follow way aligning the panel so that the ridge creates a uniform gap all around the panel to the frame.

Where the stiles and rails connect each other, apply glue in those joints. On the panel, don’t use glue. Hold the panel when necessary. You can do it with two-pin nails. In these positions, a glue drop serves a similar motive. For about an hour, the door will rest in clamps.

Now sand the flush of the joints. Your door is ready to install. After installing, paint your full-length storage cabinet. Now, your cabinet is ready to use.


How to build full-length storage drawers?

You need to take some steps –
• Make a basement for making cabinets
• How to make plywood for the base cover
• Trim the start and end of the garage’s cabinets.
• Cut side pieces and backboards
• Side pieces help balance; place them at the bottom of the cabinet
• Give the backboard stability in the cabinet
• Cut out the middle board and shelf

How to quickly make a homemade storage bench?

First, you need to add the base and cut. Then make a thin wooden frame and cut the side of the wood. Make upholstery with liner from plywood. The next step is to put the woods together. Finally, attach the grooves and turn them into storage.

Which plywood need you to use for parking cabinets?

Hardwood plywood is using for your parking shelves. These cabinets will remain dependent on the looks and capacity you want. As suggested, plywood is an excellent option when the ending of the outlets is essential.

How much does it cost to build a storage cabinet?

If you’re considering a new storage cabinet in your home, it’s important to know the average cost. The price for custom cabinets can vary widely depending on size and what type of wood is used.
The average homeowner can expect to pay $500 to $1,200 per linear foot for custom cabinets or $2,269 and $8,434 for the average kitchen with 25 linear feet. A bathroom or office will run about 4 grand to 10 grand. People are reporting that they typically spend an average of 5 thousand dollars, but there is a range from 2k-8k.

How deep should storage cabinets be?

It depends on what you plan to put inside it. If you are using a custom-built storage cabinet, for example, the depth will depend on how many shelves or compartments there are and where they are positioned. Typically, a 16″ (40.6cm) to 24 ” (60.96cm) deep storage cabinet is sufficient for most people’s needs; however, some may need deeper cabinets if they have bulky items like large tools that can’t fit in smaller ones without being stacked up high.


Now, you can securely keep your things in your full-length storage cabinet. Hopefully, you can know now how to build a full-length storage cabinet. Follow the method and make a cabinet by yourself. This cabinet can save your room space. is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising & linking to Amazon properties including, but not limited to, ||| Copyright© 2022 • All Right Reserved.